
Galvanised and coated mesh fences: what the finishes do
Most mesh panels are galvanised, coated in colour, or both. Knowing what each layer does helps you choose a fence that suits the coast or the countryside.
What does galvanising do?
In short: it covers the steel with a zinc layer that protects it from corrosion, even sacrificing itself around small scratches.
Plain steel rusts quickly outdoors. Galvanising coats the steel with zinc, which forms a barrier against moisture and, unlike paint, continues to protect bare steel at small scratches by corroding in its place. That is why galvanised panels and posts are the basis of almost every mesh fence.
A galvanised-only fence has a grey metallic look, which some owners like on industrial or rural sites. Over time the surface dulls, which is normal. We do not quote zinc thicknesses or lifespans; these depend on the product and the environment, and the supplier's documentation is the place to check them.

What does a coloured coating add?
In short: a polymer coating, often polyester powder, applied over the galvanising, which adds colour and a second barrier against corrosion.
Coloured panels – green, anthracite, black and others – are usually galvanised first and then coated, often with a polyester powder that is baked on. In Spain this is commonly called plastificado. The coating gives the fence its colour and a second barrier: water has to get through the coating before it reaches the zinc.
The weak points are where the coating is broken: cut edges, drilled holes, scratches from tools or vehicles. Those spots need touching up. On our 3D panel and 2D panel pages you can see both galvanised and coated fences we have built.

Does the coast need a different finish from inland?
In short: salty air is harder on steel, so on the coast a galvanised and coated finish and regular rinsing are especially worthwhile; inland, dust and vegetation matter more.
Along the coast of Málaga province, sea spray and salty air settle on every surface. Salt draws moisture and speeds up corrosion, especially where water sits: the bottom of posts, joints, clips. A double protection – galvanised and coated – is a sensible choice there, together with occasional rinsing with fresh water.
Inland, the challenges are different: dust, irrigation water, fertilisers, and vegetation growing into the fence. Keeping plants off the mesh and clearing soil from the bottom of the posts helps most. Our area pages, such as Málaga and Campillos, describe local considerations in general terms.
Where does corrosion usually start?
In short: at cut edges, scratches, the bottom of posts, and anywhere soil, leaves or water stay in contact with the steel.
When we look at older mesh fences, corrosion almost always starts in the same places:
- Cut panel ends, where the wire core is exposed
- Scratches from strimmers, ladders or vehicles
- Post bases, where water and soil collect
- Clips and screws, especially if they are of a different material from the post
- Contact with soil or vegetation that keeps the steel damp
Good installation reduces these risks: treating cut edges, fitting post caps, keeping the bottom of the panels clear of soil and using matching fixings. Our posts and clips guide explains the fixing side.

How should you look after a coated fence?
In short: rinse it occasionally, keep vegetation off, inspect for scratches and touch them up before rust spreads.
Coated mesh does not need painting, but it does reward a little attention:
- Rinse with fresh water from time to time, more often on the coast.
- Do not use abrasive cleaners or pressure washers at close range, which can damage the coating.
- Keep hedges and climbers from growing through the panels.
- Touch up scratches with a paint suited to coated steel after cleaning the spot.
- Check the bottoms of posts once in a while.
If you are abroad, ask whoever looks after the property to send you a few photos of the fence each season.
How do you choose the right finish?
In short: decide on looks and setting first – galvanised for a plain, industrial look, galvanised and coated for colour and extra protection, especially near the sea.
For warehouses, plots and rural parcels, plain galvanised panels are a common, practical choice; see our warehouse fencing and plot fencing pages. For villas, gardens and community grounds, coloured coated panels blend better and add a second layer of protection. If the community or urbanisation sets a colour, follow it.
Whatever you choose, the quality of installation – protected cut edges, correct fixings, a clear base – makes as much difference as the finish itself.
Articles and guides

3D mesh panel fence: the folded welded panel, properly installed
The 3D panel is the rigid mesh you see around villas and new housing across the province. We build it on proper footings, with or without a base, from setting out to clean-up.
View details →
2D double-wire mesh panel fence for sites that need a stiffer panel
The 2D panel is flat, heavy-looking and stiff, with each vertical wire held between two horizontal wires. We build it on proper footings for commercial, community and residential boundaries.
View details →
Posts and clips: what really holds a mesh panel fence up
Owners choose panels by colour and style, but a mesh fence stands or falls on its posts, their footings and the clips that join everything together.
View details →
Mesh panel fencing in Málaga city
In Málaga city we build 3D and 2D mesh panel fences, fences on precast bases and metal sheet fences for homes, residents' communities, vacant plots and business premises.
View details →Frequently asked questions
What is plastificado?
It is the Spanish term commonly used for a coloured polymer coating on a fence, often polyester powder applied over galvanised steel.
Is galvanised enough without a coating?
On many inland and industrial sites it is a common choice. Near the sea, a coating on top adds a valuable second barrier.
Which colour lasts best?
We do not make claims about colour durability. Ask the supplier for the product's documentation; availability also depends on the supplier.
Can I paint a galvanised fence?
It is possible, but galvanised steel needs suitable preparation and primer. It is usually better to choose a coated panel from the start.
Why are my fence posts rusting at the bottom?
Water and soil sit at the base of posts. Keeping the base clear and the coating intact helps; severe rust may need post replacement.
Do cut panels rust faster?
Cut ends expose the steel, so they are a weak point. We treat cut edges after cutting them on site.
Should I rinse a fence near the beach?
Yes, rinsing occasionally with fresh water removes salt deposits that speed up corrosion.
Can scratches be repaired?
Yes. Clean the spot and apply a touch-up paint suitable for coated steel. Do it early, before rust spreads.
Do sheet fences use the same finishes?
Sheet is usually galvanised and may be coated too. Cut edges and screw holes are the main weak points.
Do you give a lifespan figure for finishes?
No. Lifespan depends on the product, the setting and maintenance, and we do not quote figures we cannot back up.
Send photos and the length of your fence line
We build the whole fence – groundwork, base, posts and panels. Send photos and the approximate length for a first assessment and an itemised quote, no commitment.