
Posts and clips: what really holds a mesh panel fence up
Owners choose panels by colour and style, but a mesh fence stands or falls on its posts, their footings and the clips that join everything together.
Why do posts matter more than panels?
In short: the panel only spans between posts; every load – wind, a leaning person, a dog jumping – ends up in the post and its footing.
A rigid mesh panel is a strong, light element, but it does not stand on its own. It hangs between two posts, and anything that pushes on the panel is passed to them. If a post is undersized, badly set or sitting in a shallow footing, the fence leans, the panels twist and the clips work loose.
That is why, when we assess a line, we look at the ground and the footings before we talk about panels. A fence with modest panels on well-set posts outlasts an expensive panel on a poor footing. The same principle applies to 3D panels, 2D double-wire panels and, even more so, to sheet fences, which catch wind across their whole face.
What kinds of posts are used with mesh panels?
In short: mostly steel posts of rectangular or square section, either with clips or brackets fixed on the face, or with slots and hooks built into the post.
There are many post systems on the market, but they fall into a few families:
- Rectangular or square posts with separate clips. The panel sits against the face of the post and is held by clips that wrap around the wires and screw into the post.
- Posts with integrated hooks or slots. The panel hooks onto the post, and a cover or wedge locks it in place. Quick to install, but the panels and posts must belong to the same system.
- Posts designed for base plates. These have slots or brackets for precast concrete plates at the bottom, as described on our precast base page.
- Posts fixed on a wall with a base plate and anchors, used where the fence sits on a low wall.
The right choice depends on the panel, the base and the site. What matters most is that every component belongs to one compatible system.

What do the clips actually do?
In short: they lock the panel wires to the post so the panel cannot lift, slide or rattle – and they must match both the post and the panel wire.
Clips are small parts with a big job. A clip holds the horizontal wires of the panel against the post and stops the panel lifting off or sliding along the line. On a 3D panel, clips are often placed near the folds; on a 2D double-wire panel, they hold the paired wires together against the post.
The most common problem we see on older fences is mismatched or missing clips: a panel fixed with a clip designed for another post or another wire thickness, or held with wire ties because the clips ran out. These fences rattle in the wind, and over time the panels loosen. When a client supplies their own material, checking clips against posts is one of the first things we do.
How are posts set in the ground?
In short: each post goes into a concrete footing sized to the ground and the load; on a low wall, posts are anchored or embedded into the wall.
For posts set in the ground, we dig a hole for each post, set the post plumb and in line, and fill with concrete. The size of the footing depends on the ground, the height of the fence and the infill: mesh lets wind through, sheet does not. We do not quote fixed dimensions from memory; we decide them on site and they appear in the itemised quote.
On a built low wall, posts can be embedded in the wall as it is built, or fixed later with a base plate and anchors. Embedding usually gives a stronger joint; surface fixing depends on the wall being sound. Our guide on bases on sloping ground covers how posts work with stepped bases.

What happens at corners, ends and changes of level?
In short: these are the points under most strain, and they need correct post spacing, cut panels with protected edges and, where the system requires, special fixings.
Straight runs are the easy part. Corners, ends and steps concentrate the loads and need planning. At a corner, the panels meet at an angle and the post takes load from two directions. At an end, the post has panel on one side only. At a step, the panel heights change and the clips are at different levels.
Panels often have to be cut to fit the last bay of a run. Cutting exposes bare steel at the wire ends, so we treat cut edges to protect them. Our finishes guide explains why that matters, particularly near the coast.
How can you check an existing fence's posts and clips?
In short: walk the line, push gently on each panel, look for leaning posts, cracked footings, loose or missing clips and rust at the base of the posts.
If you are buying a property with an existing mesh fence, or managing one from abroad, a simple check tells you a lot:
- Look along the line from one end: posts should be straight and panels aligned.
- Push gently on panels: a little give is normal, rattling is not.
- Count the clips: every post should have the full set.
- Look at the bottom of each post for rust and cracked concrete.
- Check corners and ends, where problems show first.
If several posts lean or footings have cracked, repair is often a partial rebuild. We can assess it from photos and quote the work as part of a new or rebuilt fence.
Articles and guides

3D mesh panel fence: the folded welded panel, properly installed
The 3D panel is the rigid mesh you see around villas and new housing across the province. We build it on proper footings, with or without a base, from setting out to clean-up.
View details →
2D double-wire mesh panel fence for sites that need a stiffer panel
The 2D panel is flat, heavy-looking and stiff, with each vertical wire held between two horizontal wires. We build it on proper footings for commercial, community and residential boundaries.
View details →
Galvanised and coated mesh fences: what the finishes do
Most mesh panels are galvanised, coated in colour, or both. Knowing what each layer does helps you choose a fence that suits the coast or the countryside.
View details →
Bases on sloping ground: stepping a mesh fence down a hill
Málaga province is full of slopes, from hillside urbanisations to inland fincas. Rigid panels do not bend, so the way the fence and its base deal with the fall needs planning.
View details →Frequently asked questions
Can I use posts from one brand with panels from another?
Sometimes, but it is a common source of problems. Posts, clips and panels should belong to one compatible system; we check before installing.
Are clips really necessary on every post?
Yes. Each post needs its full set of clips for the panel to stay in place and not rattle in the wind.
Can posts be fixed onto an existing wall?
Yes, if the wall is sound and wide enough. Posts can be fixed with a base plate and anchors; we inspect the wall first.
Why do some fences rattle in the wind?
Usually because clips are missing, loose or the wrong type for the post or wire. Fitting the correct clips often fixes it.
How deep should the footings be?
It depends on ground, height and the type of infill. We decide on site and list footings separately in the quote rather than quoting a standard figure.
Do sheet fences use the same posts?
Not usually. A sheet fence needs rails and a heavier structure because the sheet catches the wind. See our metal sheet page.
What are post caps for?
They close the top of hollow posts to keep water and debris out, which helps prevent corrosion inside the post.
Can a leaning post be straightened?
Sometimes a recently set post can be reset, but a post leaning because its footing has failed usually needs a new footing.
Are cut panel edges a problem?
They are a weak point for corrosion because the protective layers are cut away. We treat cut edges after cutting.
Can you assess my fence from photos?
Yes. Clear photos of the whole line, the corners and close-ups of posts and clips are enough for a first opinion.
Send photos and the length of your fence line
We build the whole fence – groundwork, base, posts and panels. Send photos and the approximate length for a first assessment and an itemised quote, no commitment.