
3D mesh panel fence: the folded welded panel, properly installed
The 3D panel is the rigid mesh you see around villas and new housing across the province. We build it on proper footings, with or without a base, from setting out to clean-up.
A 3D mesh panel fence is a fence of welded steel wire panels with horizontal V-shaped folds that stiffen the panel, fixed with clips to steel posts set in concrete; in Spain it is widely known as a Hércules panel.
What is a 3D mesh panel?
In short: a flat welded wire panel given horizontal V-shaped folds, which make it rigid enough to stand between posts without sagging.
A 3D panel starts as a grid of vertical and horizontal steel wires welded at every crossing. During manufacture the panel is pressed to form horizontal folds – the ribs you see as a shallow V across the face. Those folds give the panel its stiffness, and they are why it is called "3D": the panel has depth, not just width and height.
In Spain the same product is often sold as a Hércules panel, after the generic name the trade has adopted. The panels come galvanised, coated, or both, and are fixed to posts with clips or brackets specific to the post system. Our guide to posts and clips explains the different fixing systems and why mixing them causes problems.
The result is a see-through fence: it marks the boundary and keeps dogs and people out, while leaving the view and the light.

Which plots and properties does a 3D fence suit?
In short: gardens, villa boundaries, community grounds and rural parcels where you want a firm, open fence rather than a solid wall.
The 3D panel is the everyday rigid fence. It works well for:
- Villa and townhouse gardens where owners want to keep a sea or mountain view
- Keeping dogs in, particularly when combined with a base that stops digging
- Comunidad gardens and play areas
- Boundaries with a neighbour (the lindero), where a solid wall would need more agreement
- Orchards and smallholdings inland
It is less suited to places where privacy is the main goal – mesh is see-through by design – or to high-security sites, where a 2D double-wire panel or a dedicated security design may be the better starting point. Our comparison of 2D and 3D panels looks at the trade-offs in detail.

Should it go on a low wall or straight on posts?
In short: both work – a base or murete gives a cleaner edge and stops digging, posts straight into footings keep the job simpler and leave the ground open.
There are three common ways to build a 3D fence:
- Posts in individual footings, with the panel bottom just above the ground. The simplest build and the most open, but animals can dig under and grass grows through.
- On a precast concrete base: base plates slot between the posts and give a continuous edge. See our page on the mesh fence on a precast base.
- On a built low wall (murete): posts are fixed on top of or into the wall. This suits sloping ground and owners who want a more solid look at the bottom.
On slopes, the base also decides how the fence steps. Our guide to bases on sloping ground explains stepping versus following the slope.

What should you check before building (rules, boundary)?
In short: confirm the boundary line, the town's and the urbanisation's rules on height and finish, and whether the ayuntamiento needs a licence or a declaración responsable.
Before we set out a single peg, three things need to be clear.
The boundary. Where is your lindero exactly? If there are old markers, a survey or a notary plan, we work from that. If the neighbour disputes the line, that has to be settled first – we build where the owner instructs, and moving a fence later costs more than measuring twice.
The rules. Height limits, whether the bottom must be solid, and allowed colours are set by the town's PGOU and ordinances, and in many urbanisations by the community's statutes too. We do not quote figures from memory; ask the ayuntamiento or your administrator (check for your address).
The paperwork. Whether the fence needs a licence or a simpler notice depends on the town. The owner or their gestor presents it; we provide a clear description of what we will build.
How do you look after a 3D fence?
In short: very little – rinse off salt and dust now and then, keep vegetation off the panels, and touch up any scratch that reaches bare metal.
A well-installed galvanised and coated panel needs little care, but a few habits help it age well, especially near the sea:
- Rinse the panels with fresh water occasionally if you are on the coast, where salt deposits build up.
- Keep climbing plants and hedges from growing through the mesh; they hold moisture against the steel and push panels out of line.
- Check clips and post caps once in a while, particularly after strong wind.
- If a strimmer or a car scratches through the coating, clean the spot and touch it up with a suitable paint.
Our guide to galvanised and coated finishes explains what each layer does and why the cut edges matter.

What affects the cost of a 3D fence?
In short: length, height, finish, base type, foundations, ground conditions, access and any old fence removal – we price each item separately.
A 3D fence can be a modest job or a substantial one depending on what sits under it. The panel itself is only part of the cost; groundwork, base and access often decide the final figure. The list of cost factors on this page shows what we look at, and the itemised quote shows how each one is priced for your line.
For a fuller explanation of how fence quotes are built, see our article on what affects fence cost in 2026 and the price-focused site presupuestovalla.eu.
How we build it – step by step
- Setting out
We mark the agreed line with pegs and string from your boundary markers, and check levels along the run.
- Excavation
We dig the post holes, and the strip for a base where the design includes one, removing roots and loose fill.
- Foundations
Concrete footings are poured for each post, or a continuous foundation where a wall or base will sit on it.
- Base or low wall
Where specified, precast base plates are placed or a low wall (murete) is built and capped.
- Posts
Posts are set plumb and in line, braced while the concrete cures, and checked again before panels go on.
- Panels
Panels are hung and fixed to the posts with the clips designed for that post system, stepping where the ground falls.
- Finishing
We check alignment and fixings, touch up any damaged coating and fit post caps.
- Clean-up and handover
Spoil, offcuts and packaging are removed and we walk the line with you or send photos if you are abroad.
When is it the right choice – and when not?
A good fit if…
- Villa and garden boundaries where you want to keep the view
- Keeping dogs in, especially on a base
- Community gardens and shared areas
- Rural parcels and orchards
- Neighbour boundaries where a solid wall is not wanted
Consider another option if…
- Privacy screening – mesh is see-through
- Holding back soil – a fence is not a retaining wall
- High-security sites without a proper security design
- Owners who want a gate from us – gates are not part of our service
What affects the cost?
We don't publish fixed prices: every fence is quoted line by line using these factors.
- Linear metres of fence
- Fence height
- Finish: galvanised, coated or both
- Posts in footings, precast base or built low wall
- Foundation type and depth required by the ground
- Ground conditions: rock, fill, roots
- Slope and the number of steps
- Access for materials and machinery
- Removal of an old fence and clearing of the line
- Licence paperwork (owner's responsibility)
Articles and guides

2D double-wire mesh panel fence for sites that need a stiffer panel
The 2D panel is flat, heavy-looking and stiff, with each vertical wire held between two horizontal wires. We build it on proper footings for commercial, community and residential boundaries.
View details →
Mesh fence on a precast concrete base: a clean edge at ground level
Concrete base plates slot in between the posts and close the gap under the panels. It is the tidy way to finish a mesh fence on lawns, gravel and gardens with dogs.
View details →
2D vs 3D mesh panels: which one suits your property?
Both are rigid welded mesh panels on steel posts, but they are built differently and suit different jobs. Here is how to choose without the sales talk.
View details →
Posts and clips: what really holds a mesh panel fence up
Owners choose panels by colour and style, but a mesh fence stands or falls on its posts, their footings and the clips that join everything together.
View details →
Galvanised and coated mesh fences: what the finishes do
Most mesh panels are galvanised, coated in colour, or both. Knowing what each layer does helps you choose a fence that suits the coast or the countryside.
View details →Frequently asked questions
Is a 3D panel the same as a Hércules panel?
In everyday Spanish trade use, yes. Hércules has become a generic name for folded welded mesh panels, much as people use a brand name for a product type.
Why does the panel have folds?
The V-shaped folds stiffen the panel so it stays flat and straight between posts. A flat panel of the same wire would flex more.
Can a 3D fence keep my dog in?
Generally yes, if the height suits the dog and the bottom is closed off. A base or low wall stops digging under the fence.
Will it rust near the sea?
Galvanised and coated panels resist corrosion well, but salt air is demanding. Rinsing now and then and touching up scratches keeps it in good condition.
Can you build it on my existing wall?
Often yes, if the wall is sound and wide enough to take post fixings. We check the wall before quoting; a cracked or leaning wall needs attention first.
What colours can I choose?
Green, anthracite and plain galvanised are common. What is available depends on the supplier when we order.
Can I add privacy strips?
Privacy screening is not something we supply or fit. If you want privacy, a solid option such as a metal sheet fence or a different fence type may suit better.
Do you install the gate as well?
No. Gates are not part of our service. We can leave the agreed opening in the line so your gate supplier can fit one.
How is the fence fixed to the posts?
With clips or brackets designed for the specific post system. Using the right fixings for the post is essential; mismatched parts work loose.
Can the fence follow a slope?
Yes. Panels can be stepped down a slope, and on gentle slopes a base can follow the ground. We decide the approach with you at setting out.
Send photos and the length of your fence line
We build the whole fence – groundwork, base, posts and panels. Send photos and the approximate length for a first assessment and an itemised quote, no commitment.