
2D double-wire mesh panel fence for sites that need a stiffer panel
The 2D panel is flat, heavy-looking and stiff, with each vertical wire held between two horizontal wires. We build it on proper footings for commercial, community and residential boundaries.
A 2D double-wire mesh panel fence is a fence of flat welded steel panels in which each vertical wire is clamped between a pair of horizontal wires, giving a stiff panel without folds, fixed to steel posts set in concrete.
What is a 2D double-wire panel?
In short: a flat welded panel built with pairs of horizontal wires around each vertical wire, which gives it stiffness without the folds of a 3D panel.
Where a 3D panel gets its rigidity from folds, a 2D panel gets it from the wire layout. Each vertical wire sits between two horizontal wires, welded at every crossing, so the panel has a doubled horizontal structure. The face is flat, the lines are straight, and the overall look is heavier and more architectural.
Because the face is flat, 2D panels are popular on commercial premises, public buildings and modern houses where a clean, uniform line matters. They are supplied galvanised, coated or both, and are fixed to posts with a fixing system that suits the double wires. Our guide to posts and clips covers the main options.

Where does a 2D panel make most sense?
In short: on commercial and community sites, along roads and car parks, and on homes where a flat, solid-looking mesh is preferred.
Typical uses for 2D double-wire fencing include:
- Business premises and yards on industrial estates
- Car parks and access roads where the fence takes knocks
- Community grounds where the fence must look tidy for a long time
- Modern houses where the owner prefers a flat face to the folded look
For large perimeters around naves, see our dedicated page on warehouse fencing. If you are weighing up the two panel types, our 2D vs 3D comparison sets them side by side without the sales talk.

Should a 2D fence sit on a base?
In short: often yes on commercial sites, where a continuous base keeps the bottom line clean and closes the gap under the panels.
A 2D fence can go straight on posts in footings, on a precast base, or on a built low wall. On commercial and community sites, a base is common because it gives a continuous, easy-to-clean edge and stops litter, animals and people slipping under the panels.
On level ground, a precast base is the quickest way to get that edge – see the precast base page. On slopes, or where the fence has to match an existing wall, a built murete may be better. We set out both options in our guide to bases on sloping ground.

What should be checked before building?
In short: the boundary line, any planning or estate rules on height and finish, underground services along the line, and access for materials.
On business premises, underground services are often the first surprise: drainage, cables and water pipes along a boundary are common. Before we dig, we ask for any plans you have and look for covers and markings on site. The owner should also confirm with the ayuntamiento – and, on an industrial estate, with any estate management body – what height and finish are allowed, and whether a licence or notice is needed (check for each site).
Our guide to warehouse boundary rules covers what to check on industrial land.
How do you maintain a 2D fence?
In short: occasional washing, checking fixings after knocks or wind, and touching up any damaged coating promptly.
2D panels are robust, but commercial fences take more knocks than garden fences. A delivery van or a pallet truck can bend a panel or chip the coating. Check the line from time to time, especially near loading areas, and repair damage early: a bent panel can usually be replaced on its own, and a scratch touched up before it spreads.
Near the sea, rinse off salt now and then. Inland, dust and vegetation are the main enemies; keep weeds and climbing plants off the mesh.

What affects the cost of a 2D fence?
In short: the same factors as any rigid fence – length, height, finish, base, foundations, ground, access and removal of an old fence.
2D panels are a more substantial product than 3D panels, and they often go on sites where a base and stronger footings make sense. Each of those choices is a separate line on our quote. The cost factors listed on this page are the ones we measure and price.
If you want to understand how to compare quotes from different contractors, read our 2026 cost article or visit presupuestovalla.eu.
How we build it – step by step
- Site check and setting out
We confirm the line, look for underground services and peg out the run with levels taken along it.
- Digging
Post holes are dug, and the trench for a base where one is specified; hard standing is cut where the line crosses it.
- Footings
Each post gets a concrete footing sized to the ground; a strip foundation is poured where a low wall will sit.
- Base
Precast plates are seated between the posts, or the low wall is built and finished, where included.
- Setting the posts
Posts for the double-wire system are set vertical and in line, and checked against the string before the concrete hardens.
- Fixing the 2D panels
Panels are lifted into place and secured with the fixings made for double-wire panels; end bays are cut and their edges treated.
- Final checks
We sight along the line, tighten fixings, fit caps and touch up any marks on the coating.
- Handover
The site is cleared of spoil and packaging and the fence is handed over in person or with photos.
When is it the right choice – and when not?
A good fit if…
- Business premises and industrial yards
- Car parks and access roads
- Community grounds needing a tidy, uniform line
- Modern houses where a flat face is preferred
Consider another option if…
- Privacy – the panel is see-through
- Retaining soil or acting as a wall
- Sites where a gate must be supplied by the fencing contractor – we do not supply gates
- Very tight budgets where a lighter panel would do the job
What affects the cost?
We don't publish fixed prices: every fence is quoted line by line using these factors.
- Linear metres
- Fence height
- Panel finish
- Base: none, precast or built low wall
- Footings and foundations
- Ground conditions and underground services
- Slope and stepping
- Access for vehicles and materials
- Old fence removal and line clearing
- Number of corners and ends
Articles and guides

3D mesh panel fence: the folded welded panel, properly installed
The 3D panel is the rigid mesh you see around villas and new housing across the province. We build it on proper footings, with or without a base, from setting out to clean-up.
View details →
Warehouse fencing for naves, yards and industrial plots
Long, straight runs around a nave, a loading yard or an empty industrial plot. We plan the line around your operations and build it on proper foundations, with mesh panels or metal sheet.
View details →
2D vs 3D mesh panels: which one suits your property?
Both are rigid welded mesh panels on steel posts, but they are built differently and suit different jobs. Here is how to choose without the sales talk.
View details →
Warehouse boundary rules: what to check before fencing industrial land
Fencing a nave or an industrial plot involves the same duties as any property, plus estate rules, street frontages, services and a business that has to keep running.
View details →
Posts and clips: what really holds a mesh panel fence up
Owners choose panels by colour and style, but a mesh fence stands or falls on its posts, their footings and the clips that join everything together.
View details →Frequently asked questions
What does 2D mean in a mesh panel?
It means the panel is flat, without the folds of a 3D panel. Its stiffness comes from the double horizontal wires instead.
Is 2D stronger than 3D?
A 2D double-wire panel is generally stiffer than a folded panel, which is why it is common on commercial sites. Which one you need depends on the site, not just strength.
Is a 2D fence suitable for a house?
Yes. Many owners choose it for its flat, modern look. It is usually a more substantial product, so it suits owners who want a heavier fence.
Can you combine 2D panels with an existing wall?
Often yes, if the wall is in good condition. We assess the wall before deciding how to fix the posts.
Which posts are used with 2D panels?
Steel posts with a fixing system designed for double-wire panels. The post system must match the panels; we check this before ordering or installing client material.
Can 2D panels be cut to length?
Yes, panels can be cut at the end of a run. Cut edges need protection, which we touch up after cutting.
Do you install anti-climb toppings?
We can discuss options for the top of the fence, but security design is a specialist matter. Our perimeter security guide explains what a fence can and cannot do.
Do you supply a gate to match?
No, gates are not part of our service. We set out the line so your gate supplier can fit the opening.
What happens if there are cables along the line?
We ask for plans, look for markings and dig carefully. If services are found where a footing should go, we agree a change with you before continuing.
Can you work while my business stays open?
Usually, yes. We plan the order of work and the storage of materials with you so that access and loading are kept as clear as possible.
Send photos and the length of your fence line
We build the whole fence – groundwork, base, posts and panels. Send photos and the approximate length for a first assessment and an itemised quote, no commitment.